English Lithurin® Rider pad

Lithurin® Rider pad

Advantages:
A polished surface with retained cement paste in the surface. No ballast or fibers appears.

The Lithurin® treatment increases the wear resistance and the density of the surface by up to 20 times.
Calcium deposits from the concrete surface is removed.
The friction on the surface is minimized, which simplifies cleaning and prevents wheel tracks from forklifts.

Treatment: HARD / SEAL
Lithurin® HARD with LC Rider Pad 320.
Lithurin® SEAL is sprayed on to the surface and then mopped off the surface with a fine mop.
Treatment: HARD / DENS / PROTEC
Lithurin® HARD with LC Rider PAD 320.
Lithurin® DENS with LC Rider PAD 800.
Lithurin® PROTEC with LC Polish PAD 1500/3000.
Conditions for new concrete surfaces
Machine troweled/finished concrete surface.
Use only water and plastic as curing. (Do not use any liquid
moisture curing).
Concrete quality of minimum C30 / C37.
The floor must be cured for at least 7 days at a temperature of
15-20°C.
The floor must be cured for at least 14 days at a temperature of
10-15°C.
With lower concrete quality, the curing time is extended.
Conditions for old concrete surfaces
Apply LimeWash to the surface. Clean/grind with LC Clean Pad 120. NOTE! Clean the surface before the sludge dries.

LAYING INSTRUCTIONS
LINDEC RIDER PAD SYSTEM
Lithurin® HARD
Lithurin® HARD is an impregnation agent which increases the density and wear resistance of the concrete surface.
Apply a minimum of 0.15 - 0.20 liters/m² Lithurin® HARD on the surface.
Apply Lithurin® HARD with a low-pressure sprayer or an LC Applicator on the surface.
Allow the material to react for about 15 min.
Polish the surface with LC Rider PAD 320 while Lithurin® HARD is liquid. NOTE! Do not let Lithurin® HARD dry before cleaning.
Thoroughly clean the surface with a combined scrubber dryer machine and water. Make sure no residue is left on the surface
when Lithurin® SEAL / DENS is applied. A smooth silky surface will appear.
Never dry polish.
Alternative Lithurin® HARD / SEAL
Lithurin® SEAL is a sealant (dust binder) which seals the surface and increases the wear resistance.
When the Lithurin® HARD treatment has dried;
Apply 0.15 liters/m² with a low-pressure sprayer or LC Applicator.
Lithurin® SEAL must remain wet on the surface for at least 15 minutes.
Mop off the surface with a fine mop.
Remove excess material while it is still liquid.
Lithurin® HARD / SEAL treatment is complete.
A glossy surface will appear.
Alternative Lithurin® HARD / DENS / PROTEC
Lithurin® DENS is an impregnating agent which densifies the concrete surface.
Apply 0.15 liters/m² Lithurin® DENS on the surface.
Apply Lithurin® DENS with a low-pressure sprayer or LC Applicator.
Mop off the surface with a fine mop and allow the surface to dry. (NOTE! It is important that the surface is saturated at the first
application.)
Polish the surface with LC Rider PAD 800 and water.
A glossy surface will appear.
For a glossier surface, polish with LC Rider PAD 1000 and water.
A shinier surface will appear.
Thoroughly clean the surface with a combined scrubber dryer machine and water. Make sure no residue is left on the surface
when Lithurin® PROTEC is applied
Alternative when low temperature which gives longer drying times.
Apply 0.15 liters/m² of Lithurin® DENS.
Apply Lithurin® DENS with a low-pressure sprayer or LC Applicator.
NOTE: It is important that the surface is saturated at the first application.
Polish the surface with LC Rider PAD 800 while Lithurin® DENS is liquid.
NOTE! Do not let Lithurin® DENS dry before cleaning.
Thoroughly clean the surface with a combined scrubber dryer machine and water. Make sure no residue is left on the surface
when Lithurin® PROTEC is applied.
Never dry polish.
Lithurin® PROTEC
Lithurin® PROTEC is an impregnation agent which increases the stain protection on the concrete surface.
Apply 0.1–0.15 liters/m² Lithurin® PROTEC on the surface.
Apply Lithurin® PROTEC on the surface with a low-pressure sprayer or LC Applicator.
Mop off the surface with a fine mop. Ensure that the surface is saturated and that Lithurin® PROTEC is evenly distributed on the
surface.
Remove excess material while it is still liquid. Allow the surface to dry.
Polish the surface with LC Polish PAD 1500/3000 and Concrete Soap mixed 1:10 with water.
Clean the surface thoroughly with a combined scrubber dryer machine and water, use water and Concrete Soap mixed 1:100
with water.
Box 5, 421 21 V. Frölunda, Sweden
+46 31 298810 [email protected]

Lindec betongprodukter

ab lindec och mer om att DAMMBINDA / DAMMBINDNING  BETONGGOLV - LITHURIN   HÅRDBETONG HARDCONCRETE - HERKULIT. Ytbehandling  BEHANDLA Härda IMPREGNERA betonggolv använd Lithuring behandlingar. Herkulit Hårdbetong ger SLITSTYRKA. För bästa betonggolv använd Herkulit  Vi har BETONG maskiner GLÄTTARE ÅKGLÄTTARE GLÄTTARBLAD